Casio IT-9000 Series Guide de l'utilisateur

Handheld Printer TerminalUser’s GuideBe sure to read “Safety Precautions” inside this guide before trying to use your Handheld Printer Terminal. ESer

E-8Power Supply / AC Adaptor WarningDo not use the Handheld Printer Terminal at a voltage other than the specifi ed voltage. Also, do not connect the H

E-9Operating PrecautionsYour Handheld Printer Terminal and its options are precision. Improper operation or rough handling can cause problems with dat

E-10Lithium-ion Battery PackEach lithium-ion battery pack has its life. The life span heavily depends on how the battery pack is charged or stored whi

E-11Important This guide does not include any information about programming and download procedures. See the applicable separate documentation for inf

E-12Regulatory InformationThe USA and CanadaGUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas).NOTI

E-13L’ utilisation de ce dispositif est autorisée seulement aux conditions suivantes :(1) il ne doit pas produire de brouillage et(2) I’ utilisateur d

E-14Checking in the BoxPlease check the contents of the box before using the Handheld Printer Terminal for the fi rst time. Open the box and make sure

E-15Handheld Printer Terminal System Confi gurationIT-9000 SeriesIT-9000E-MC25EIT-9000E-C25EThese models are available in the USA and Canada only.USB C

E-16Options AC AdaptorAD-S42120C-N5AD-S42120B-N*Screen Protect SheetHA-C90PS5BUSB Cable (to connect cradle to PC)DT-380USB-A Power Cord for Europe AC-

E-17General GuideShapes vary according to model.BackBottomLeft RightFrontTop17171612131029123784569101411151828271921242223202619251925

Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no representations or warranties with respect

E-181 Printer Prints when loaded with roll paper.2 Splash Protect Cover A splash proof cover. Slide the cover open when printing.3 Power Key Turns th

E-1917 NFC Reader Apply a card here so that the card can be accessed.18 Reset Switch Used to reset the Handheld Printer Terminal.19 Hand Strap Hook**

E-20Keys12345678910111 Function Keys These keys are used when starting a pre-registered application.2 C (Clear) Key This key is pressed when canceling

E-21Loading and Removing the Battery PackYour Handheld Printer Terminal uses two types of battery: a battery pack and a memory backup battery.The batt

E-22Loading1. Turn the terminal upside down. If the hand strap is fi tted to the terminal, remove it.2. Turn the left and right lock switches for the b

E-23Removing1. Make sure that the Handheld Printer Terminal is turned off. If the power is on, press the power key to turn it off.2. Turn the termina

E-24Charging the Battery PackBattery pack installed in the terminal can be charged using either cradle, battery charger or AC adaptor (AD-S42120C-N5/A

E-25Dual Battery ChargerTaking care that the battery pack is oriented correctly, insert it into the Dual Battery Charger.This causes the Charge Indica

E-26Handling the Hand Strap A hand strap can be attached to the Handheld Printer Terminal.Hook ARelease buttonsHand StrapHook BAttach the hand strap f

E-27Handling the Neck StrapA neck strap can be attached to the Handheld Printer Terminal to keep it from being dropped while being carried. The stylu

E-1ContentsSafety Precautions ...E-3Operating Precautions ...

E-28Removing1. Pull back the locking bar of the neck strap mounting hook and then release the hook from each ring as shown in the illustration.2. Foll

E-292. Remove Mounting Hook C.3. Pass the stylus holder through the strap as shown in the illustration.4. Fold back the strap after passing through Br

E-30Confi guring Handheld Printer Terminal SettingsCalibrating Touch Screen AlignmentWhenever the response of the touch screen is poor, or operation be

E-31Setting the Display BrightnessAdjusting Display BrightnessYou can use the following procedures to adjust display brightness to make it easier tore

E-32Using the CMOS Imager (Imager Models)1. Turn on the Handheld Printer Terminal, position its CMOS Imager reader port near the bar code or 2D code,

E-33Using the PrinterThe printer can print on roll paper (80 mm or 58 mm wide).*Installing the Roll Paper1. Check that the power is off. If the power

E-345. Close the printer cover. Turn the left and right lock switches from the "UNLOCK" position to the "LOCK" position to lock th

E-35Attaching the 58 mm Paper Width AdjusterAttach the 58 mm Paper Width Adjuster* inside the printer cover when using 58 mm wide roll paper. Refer t

E-36Precautions When Using PrinterPrinting Accuracy1. During high-duty printing such as printing horizontal lines or printing while the battery remain

E-37Others1. The temperature range for printing with label paper is 5 to 35°C.2. Once the end mark of the paper appears, promptly replace with new pap

E-2Handling Magnetic Card Reader ...E-42Handling the NFC Reader/Writer ...

E-38Handling SD Memory CardsSD memory card can be installed in the SD memory card slot on the Handheld Printer Terminal.Install (or remove) an SD memo

E-39Handling SIM/SAM CardsThe Handheld Printer Terminal supports SIM cards and SAM cards. (The IT-9000-E/05E/05E-CN/20E/25E/IT-9000E-C25E/MC25E models

E-406. Lay the SIM/SAM card cover down to close it and then slide it in the "Lock" direction.7. Fit the slot cover.8. Load the battery pack.

E-415. Remove the SIM/SAM card.6. Lay the SIM/SAM card cover down to close it and then slide it in the "Lock" direction.7. Fit the slot cove

E-42Handling Magnetic Card ReaderThe Handheld Printer Terminal supports magnetic card reading. This function is not available on some models. See P.20

E-43Handling the NFC Reader/WriterNFC is a type of RFID (Radio Frequency Identifi cation) technology that allows the data in a device to be read simply

E-44Important!Both contactless IC cards and RFID tagsThe NFC employs a low power radio wave which does not require regulatory station license. Frequen

E-45Performing CommunicationsBluetooth® CommunicationBluetooth® interface can also be used to transfer data between two Handheld Printer Terminals. Wi

E-46GSM/W-CDMA CommunicationTo use the GSM/W-CDMA functions, you must receive service from a wireless service provider. Available GSM/W-CDMA functions

E-47Resetting the Handheld Printer TerminalResetting the terminal is the same as resetting a PC. Performing a reset causes all unsaved RAM data to be

E-3Safety PrecautionsCongratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use

E-481. Hold down power key and C key while pushing down the reset switch for about 3 seconds with the tip of a stylus until the message shown below ap

E-49Warning Label Warning! (IT-9000-20E/25E/G20E/G25E/GC25E/GMC25E/IT-9000E-C25E/MC25E) Never look directly into the laser light.These products scan

E-50IT-9000 Specifi cations Model: IT-9000-05E/E/05E-CN/G05E/GE/GMC25E/GMC30E/25E/20E/G25E/G20E/GC25E/GM35E/GM30E IT-9000E-MC25E/C25ECPU: Marvell®

E-51Bluetooth®: Protocol: Bluetooth® Specifi cation Ver.2.0 + EDR Communication Range: Approximately 3 m (9'103/8") (depends on radio wave c

E-52 No. of channels: GSM 850: 124 GSM 900: 174 GSM1800 (DCS1800): 374 GSM1900 (PCS1900): 299 Channel space: 200 KHz Channel bandwidth:

E-53 Sensitivity: Acquisition sensitivity: -141 dBm Tracking sensitivity: -158 dBmSIM card: Standard: ISO 7816 IC Card standard General specifi

E-54 IT-9000-G25E/G20E: Approximately 625g (22.0oz) (with battery pack installed, not including roll paper) IT-9000-GC25E: Approximately 630

E-55Dimensional DrawingsIT-9000-05E/E/05E-CN/G05E/GEApprox.111.9mm (4 3/8")Approx.59.7mm(2 3/8")Approx.36.6mm (1 7/16")Approx. 246.3mm

E-56IT-900-GMC25E/GMC30E/GM35E/GM30E/MC25EApprox.65.8mm (2 9/16")Approx. 283.7mm (11 3/16")Approx.36.6mm (1 7/16")Approx.78.2mm (3 1/16

E-57Using the USB Cradle (HA-L60IO)The optional USB Cradle (HA-L60IO) makes it possible to transmit system data and fi le data between the Handheld Pri

E-4 WarningDust and MoistureThough the Handheld Printer Terminal is dust and water splash resistant, its options including the battery pack are not. K

E-581 Terminal Detect SwitchThis switch detects when the IT-9000 is mounted correctly on the USB Cradle.2 Mount Hooks These hooks are used to stabiliz

E-59Connecting the USB Cradle Power SupplyUse the optional AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the USB Cradle. Always make

E-604. Before using the cradle ports, remove the caps from the ports. Connect one end of the USB cable (DT-380USB-A) to the USB client port and the

E-61Status of Indicator 1 on IT-9000:Orange: Charging the battery pack.Red Flashing: Standby due to battery pack error or the surrounding temperat

E-62Specifi cations1. LAN Specifi cationsCommunications protocol: IEEE 802.3Media type: 10base-T/100base-TX auto-switched2. USBProtocol: USB Ver1.1 St

E-63Using the Ethernet Cradle (HA-H62IO)The optional Ethernet Cradle (HA-H62IO) makes it possible to transmit system data and fi le data between the Ha

E-641 Terminal Detect SwitchThis switch detects when the IT-9000 is mounted correctly on the Ethernet Cradle.2 Mount Hooks These hooks are used to sta

E-65Connecting the Ethernet Cradle Power SupplyUse the optional AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the Ethernet Cradle. A

E-664. Before using the cradle ports, remove the caps from the ports. When using a LAN, connect one end of the LAN cable to the LAN port and the oth

E-67Status of Indicator 1 on IT-9000:Orange: Charging the battery pack.Red Flashing: Standby due to battery pack error or the surrounding temperat

E-5 CautionForeign ObjectsTake care to ensure that metals or combustible objects are not inserted into the openings of the Handheld Printer Terminal

E-68Specifi cations1. LAN Specifi cationsCommunications protocol: IEEE 802.3Media type: 10base-T/100base-TX auto-switched2. USBProtocol: USB Ver1.1 St

E-69Using the Cradle-type Battery Charger (HA-L30CHG)The optional Cradle-type Battery Charger (HA-L30CHG) makes it possible to charge the battery pack

E-701 Terminal Detect SwitchThis switch detects when the IT-9000 is mounted correctly on the charger.2 Mount Hooks These hooks are used to stabilize t

E-71Connecting the Cradle-type Battery Charger Power SupplyUse the optional AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the Cradle

E-724. Push the IT-9000 fully into the Cradle-type Battery Charger until the mount hooks in the charger engage the mount holes in the IT-9000. Check

E-73Specifi cations1. Charging Charging Method: Constant current/voltageCharge Period: Approximately 5 hours2. Power SupplyPower Source: AC adaptor

E-74Using the Car Mounted-type Battery Charger (HA-L35CHG)The optional Car Mounted-type Battery Charger (HA-L35CHG) can be used to charge the battery

E-75Connecting the Car Mounted-type Battery Charger Power SupplyUse the cigarette lighter socket in the vehicle for the power supply of the Car Mounte

E-76Status of Indicator 1 on IT-9000:Orange: Charging the battery pack.Red Flashing: Standby due to battery pack error or the surrounding temperatu

E-77Specifi cations1. ChargingCharging System: Constant current/voltageCharge time: Approximately 5 hours2. Dimensions and WeightDimensions: Approx

E-6 CautionInstalling in VehicleTo save your vehicle’s battery from running down, be sure that the Car Power Cable should be unplugged from the cigar

E-78Using the Dual Battery Charger (HA-G32DCHG)The optionally available Dual Battery Charger (HA-G32DCHG) can be used to simultaneously charge two bat

E-791 Charge Indicator LEDThis LED indicates the charge status of the battery pack(s).Off: Not chargingRed: ChargingRed Flashing: Battery pack problem

E-80Charging Battery PackUse the separately sold AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the Dual Battery Charger.1. Plug the

E-81Connecting Multiple Dual Battery ChargersYou can connect up to three Dual Battery Chargers. Doing so makes it possible to supply power to all the

E-82Specifi cations1. Charging Specifi cationCharging Method: Constant current/voltage Charge Period: Approx. 4 hours (1 battery pack, normal temper

E-83Using the Rechargeable Battery Pack (HA-G20BAT)HA-G20BATImportant!Store a battery pack in its special soft case whenever you are not using it.If t

CASIO COMPUTER CO., LTD.6-2, Hon-machi 1-chomeShibuya-ku, Tokyo 151-8543, Japan2012 CASIO COMPUTER CO., LTD.

E-7Lithium-ion Battery Pack DangerNever use the Handheld Printer Terminal and its option including the battery pack and battery next to open fl ame, ne