Casio KL-8100 Guide de l'utilisateur télécharger pdf (Page 7)

E-6

To connect the AC adaptor

Remove the AC adaptor connector cover, and connect the

adaptor to the label printer as illustrated below. Plug the

other end into a standard household AC outlet.

After you finish using the label printer, turn it off and discon-

nect the AC adaptor.

• Be sure to grasp the plug of the AC adaptor cord when

disconnecting it. Never pull on the cord.

Loading/Replacing Batteries

A handy low battery power indicator lets you know when

battery power is getting too low for proper operation. The

message LOW BATTERY or REPLACE BATTERIES ap-

pears on the display if battery power is low when you per-

form any of the following operations.

• Switching power on

• Executing a print operation

• Executing a tape feed operation

You should still be able to perform some Label Printer op-

erations, but some power intensive operations (like printing

or tape feed) may become impossible if battery power is

too low. In any case, you should replace batteries as soon

as possible or switch to the AC adaptor as soon as possible

after the LOW BATTERY message appears.

Important!

Batteries can burst or leak and damage your unit if you use

them the wrong way. Note the following important points.

• Be sure that the plus (+) and minus (–) sides of each bat-

tery are facing correctly.

• Never mix batteries of different types

• Never leave dead batteries in the battery compartment.

• Remove the batteries if you do not plan to use the unit for

a long time.

• Replace the main battery in accordance with the battery

life marked on the side of the battery.

• Have the back-up battery replaced by the date noted on

the sticker on the back of the label printer.

Power On Recall Function

Whenever you turn power off, any input that is on the dis-

play is automatically stored in memory. Then the next time

you turn on power, the message “[SET] TO RECALL” ap-

pears on the display. Pressing SET when this message is

on the display recalls the text that was on the screen when

you last turned off power.

• Pressing any key besides SET, FUNC, SHIFT or CODE

clears the text from memory.

Resetting the Memory

You should reset the memory of the label printer before us-

ing it for the first time, after you have not used it for a long

time, or if nothing happens when you turn power on.

Important! Resetting label printer memory clears its

memory of all input data.

To reset the memory

1. Make sure that label printer power is off.

2. While holding down the PRINT and ESC keys, press ON

to turn power on.

?LAITI

TES

3. Press SET to initialize the label printer or ESC to abort

the reset operation without initializing anything.

• See “Initial Settings” on page E-24 for information on the

initial default settings of the label printer following the re-

set operation.

• You have to reset the Label Printer if you want to change

the on-screen message language. Press RESET and then

perform the procedure performed under Message Lan-

guage.

Auto Power Off Function

If you do not perform any key operation for about six min-

utes, the label printer automatically turns power off. To re-

store power, press ON.

Tape Cartridges

Use the procedures described below to load a tape car-

tridge into the label printer. The label printer automatically

detects what size tape is loaded.

Warning!

• Never recharge the batteries you use with this unit.

• Do not expose batteries to direct heat, do not short circuit

them, and do not try to take them apart.

•

Keep batteries out of the reach of small children. If

swallowed, consult with a physician immediately.

• Low battery power is indicated by poor print quality or

power switching off while printing is in progress.

Loading/Replacing the main batteries

1. Switch power off.

• If you are using the AC adaptor to power the unit, you

should also unplug the adaptor from the Label Printer.

2. Open the battery compartment cover on the back of the

Label Printer by sliding it in the direction indicated by the

arrow.

3. If you are replacing batteries, remove all eight of the old

batteries.

4. Load a set of eight new batteries into the battery com-

partment, making sure that their positive (+) and nega-

tive (–) ends are facing in the correct directions.

5. Replace the battery compartment cover.

Turning Power On and Off

Press ON to turn power on, and OFF to turn power off.

Important! If you are using the label printer for the first time,

you should reset it first.

1 2 3 4 5 6 7 8 9 10 11 12 ... 30 31

Commentaires sur ces manuels

Pas de commentaire

Casio KL-8100 Guide de l'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimer et scanner Casio KL-8100